A diffusive wetting model for water entry/exit based on the weakly-compressible SPH method

Shuoguo Zhang, Yu Fan, Chi Zhang, Nikolaus A. Adams, Xiangyu HuOcean 2023

TL;DR

This paper introduces a novel "diffusive wetting model" within the weakly-compressible Smoothed Particle Hydrodynamics (WCSPH) framework to simulate water entry and exit phenomena. By treating wetting as a diffusive process and coupling it with particle identification and regularization, the model accurately captures complex fluid-solid interactions, including splashing, flow separation, and free-surface breaking, across the entire entry-to-exit cycle.

What Problem Does This Paper Address?

Simulating the complex interplay of fluid dynamics and surface wettability during water entry and exit has been a significant challenge. Traditional models often simplify or neglect wettability, leading to inaccuracies, especially at later stages of impact or during water exit. Existing models struggle to capture phenomena like flow separation and spontaneous free-surface breaking during water exit, and there's a lack of a unified model that can handle both entry and exit seamlessly while accounting for wettability. This paper aims to bridge this gap by developing a robust and comprehensive model that integrates surface wettability into WCSPH simulations.

Methods

The core of the proposed method is a diffusive wetting equation that models the evolution of wetting on the solid surface. This equation is based on Fick's second law of diffusion and uses a "relative moisture" parameter to represent wetting degrees. Key innovations include:

  • Wetting-Coupled Particle Identification: A novel mechanism that identifies fluid particles near the solid surface based not only on their position but also on the wetting degree of adjacent solid particles. This ensures that fluid particles are correctly classified as "inner" or "free-surface" based on the actual wetting state.
  • Numerical Regularization: The Transport-Velocity Formulation (TVF) scheme is employed to regularize particle distribution, particularly for fluid particles near fully wetted surfaces, preventing unphysical voids and improving stability.
  • Coupling Rigid-Body and SPH: The model integrates rigid-body dynamics to simulate the motion of objects (spheres, cylinders) freely falling or rising, allowing for realistic interactions with the fluid.

Datasets

Not discussed in the paper. The paper relies on experimental data for validation rather than training datasets.

Key Insights and Ideas

  • Wetting as a Diffusive Process: Treating wetting as a diffusion-like process provides a computationally efficient yet physically consistent way to model surface wettability, avoiding the need for complex molecular-level details.
  • Unified Entry/Exit Model: The diffusive wetting approach allows for a single model to simulate both water entry and exit, recognizing water exit as the final state of the diffusive wetting process.
  • Wetting-Coupled Identification is Crucial: Simply identifying free-surface particles based on proximity to the solid is insufficient. Coupling this identification with the wetting state of the solid surface is essential for accurate simulation of wettability-affected phenomena.
  • Capturing Flow Separation and Breaking: The model's ability to accurately reproduce flow separation and spontaneous free-surface breaking during water exit, which has been a challenge for previous SPH methods, is a significant advancement.

Key Results

The paper presents several qualitative and quantitative validations:

  • 3D Water Entry of a Sphere: The model successfully reproduces various splash patterns and air entrainment phenomena observed in experiments, demonstrating its ability to capture wettability-dependent behaviors.
  • 2D Water Exit of a Cylinder: The model accurately captures flow separation and spontaneous free-surface breaking, phenomena that are difficult to simulate with traditional methods. It also reproduces the "waterfall breaking" phenomenon.
  • Complete Water Entry/Exit Process: The model successfully simulates the entire process from water entry to exit for a 2D cylinder under different wetting conditions, showing good agreement with experimental data for vertical position and velocity.
  • Resolution Independence: The use of a mapping rule in the diffusive wetting equation ensures that the results are physically consistent across different numerical resolutions.

Limitations and Future Work

  • Experimental Data for Gamma: The diffusive wetting coefficient ($\gamma$) is estimated through numerical experiments due to a lack of relevant experimental data for each specific case.
  • Coarse-Grained Model: The model is coarse-grained, meaning it abstracts away some microscopic details.
  • Future Work: The authors plan to further validate the model's performance by applying it to more complex scientific and industrial problems.

Summary updated

Abstract

This paper proposes a diffusive wetting model for the weakly-compressible smoothed particle hydrodynamics (WCSPH) method to simulate individual water entry/exit as well as the complete process from water entry to exit. The model is composed of a physically consistent diffusive wetting equation to describe the wetting evolution at the fluid-solid interface, a wetting-coupled identification approach to determine the type of fluid particles by taking into account the wetting degree of the contacted solid, and a numerical regularization on the fluid particles at fully wetted fluid-solid interface. The accuracy, efficiency, and versatility of the present model are validated through qualitative and quantitative comparisons with experiments, including the 3-D water entry of a sphere, the 2-D water entry/exit of a cylinder, and the complete process from water entry to exit of a 2-D cylinder.
BibTeX
@inproceedings{zhang2023diffusive,
  author = {Shuoguo Zhang and Yu Fan and Chi Zhang and Nikolaus A. Adams and Xiangyu Hu},
  title = {{A diffusive wetting model for water entry/exit based on the weakly-compressible SPH method}},
  booktitle = {Ocean},
  year = {2023},
}
Figure