50-Gb/s PDM-DMT-SSB transmission over 40km SSMF using a single photodetector in C-band

Jiahao Huo, Xian Zhou, Kangping Zhong, Tao Gui, Yiguang Wang, Liang Wang, Jinhui Yuan, Hongyu Zhang, Keping Long, Changyuan Yu, Alan Pak Tao Lau, Chao LuOFC 2017

Introduction

As data centers and short-reach networks face exploding bandwidth demands, engineers are hunting for ways to increase spectral efficiency (SE) without the high cost and power consumption of coherent detection—the gold standard for long-haul fiber. The industry currently relies on Intensity Modulation/Direct Detection (IM/DD) because it is cost-effective and simple. However, IM/DD systems are limited by two major factors: chromatic dispersion (CD), which causes frequency-selective power fading over distance, and signal-to-signal beating interference (SSBI).

To mitigate dispersion, researchers often employ Single-Sideband (SSB) modulation. However, SSB requires a "guard band"—an empty frequency gap—to prevent interference from ruining the signal during direct detection. This gap represents wasted spectral real estate. This paper demonstrates a novel Polarization-Division Multiplexing (PDM) DMT-SSB scheme that "recycles" this wasted guard band to double the data rate while maintaining a simple single-photodetector receiver architecture.

Proposed Architecture and Spectrum Packing

The core innovation of this work is the clever arrangement of signals in the frequency and polarization domains. On the X-polarization, the system transmits an SSB-OFDM signal with a dedicated guard band. Simultaneously, on the Y-polarization, a Discrete Multi-Tone (DMT) signal is transmitted. Crucially, the DMT signal is frequency-shifted so that its spectrum occupies the exact frequency range of the X-polarization's guard band.

Frequency spectrum allocation and detection: (a) X-pol SSB signal, (b) Y-pol DMT signal, (c) combined PDM signal, and (d) the electrical spectrum after square-law detection.

As shown in the figure above, when these signals are combined and detected by a single photodetector, the detector acts as a square-law device. This mixing process maps the two independent polarization channels into a single electrical stream. While this creates interference, the specific frequency mapping ensures that the primary signal components are separable in the digital domain.

Experimental Setup

The researchers validated this approach using a laboratory testbed consisting of a 40km link of Standard Single-Mode Fiber (SSMF) in the C-band. The experimental setup utilizes two Arbitrary Waveform Generators (AWGs) to drive an I/Q modulator for the SSB signal and an Intensity Modulator (IM) for the DMT signal.

Experimental setup for the 50-Gb/s PDM-DMT-SSB transmission system.

Key components of the setup include:

  • Optical Modulators: A Polarization Beam Splitter (PBS) divides the laser source into X and Y polarizations. The X-pol is modulated with a 14 GHz wide SSB-OFDM signal (16QAM), while the Y-pol is modulated with a 7 GHz DMT signal using adaptive bit-loading.
  • Transmission: The signals are recombined via a Polarization Beam Combiner (PBC) and sent through 40km of SSMF.
  • Receiver: A single photodetector (PD) performs direct detection, followed by a Digital Storage Oscilloscope (DSO) for data capture.
  • DSP Offline: A sophisticated Digital Signal Processing (DSP) chain handles the demultiplexing and interference cancellation.

Digital Interference Cancellation and Results

Because the signals from both polarizations are mixed at the photodetector, the SSB signal generates nonlinear SSBI that overlaps with the DMT signal. The authors treat this SSBI not as random noise, but as a deterministic distortion. Since the receiver can clearly see the high-frequency components of the SSB signal, the DSP algorithm uses that information to estimate the interference and subtract it from the DMT signal.

The system successfully achieved a 50-Gb/s transmission rate over 40km with a Bit Error Rate (BER) of $3.8 \times 10^{-3}$, which falls within the limits for standard Hard-Decision Forward Error Correction (HD-FEC). The receiver sensitivity reached the BER limit at -7 dBm, with a remarkably low transmission penalty of only 1 dB compared to a back-to-back (BTB) configuration.

Conclusion and Future Outlook

This PDM-DMT-SSB scheme demonstrates that it is possible to significantly increase the spectral efficiency of short-reach links without moving to full coherent detection. By exploiting the deterministic nature of SSBI and the low polarization crosstalk over short distances, the researchers effectively doubled the capacity of the available spectrum.

Future work will likely focus on addressing the "BER floor" observed at high power levels due to photodetector saturation and optimizing the DSP algorithms for real-time hardware implementation. While currently limited to distances where polarization remains relatively stable, this technique offers a promising path for high-capacity, low-cost data center interconnects.

Summary updated

BibTeX
@inproceedings{huo2017gb,
  author = {Jiahao Huo and Xian Zhou and Kangping Zhong and Tao Gui and Yiguang Wang and Liang Wang and Jinhui Yuan and Hongyu Zhang and Keping Long and Changyuan Yu and Alan Pak Tao Lau and Chao Lu},
  title = {{50-Gb/s PDM-DMT-SSB transmission over 40km SSMF using a single photodetector in C-band}},
  booktitle = {OFC},
  year = {2017},
}
Figure