3D Printing Fiber Electrodes for an All‐Fiber Integrated Electronic Device via Hybridization of an Asymmetric Supercapacitor and a Temperature Sensor

Jingxin Zhao, Yan Zhang, Yinan Huang, Jixun Xie, Xiaoxin Zhao, Chaowei Li, Jingyi Qu, Qichong Zhang, Juan Sun, Bing He, Qiulong Li, Conghua Lu, Xinhua Xu, Weibang Lu, Liqiang Li, Yagang YaoAdvanced 2018 · DOI

TL;DR

Researchers have developed a novel 3D printing technique to create integrated, wearable electronic devices that combine energy storage (supercapacitors) and sensing (temperature sensors) in a flexible fiber format. This low-cost, scalable method addresses limitations in current wearable electronics, enabling a single fiber to power and monitor temperature, paving the way for more advanced smart textiles and health monitoring systems.

What Problem Does This Paper Address?

The field of wearable electronics is rapidly advancing, with a strong demand for flexible and comfortable devices. While fiber-shaped supercapacitors (FASCs) offer promising energy storage solutions for wearables, their practical application is hindered by challenges in fabrication cost, efficiency, and scalability. Furthermore, integrating these energy storage components with sensing functionalities, like temperature monitoring, into a seamless fiber format has remained a significant hurdle. Existing methods often struggle with complex fabrication processes and limited scalability, preventing widespread adoption. This paper tackles these issues by proposing a simple, cost-effective, and highly scalable 3D printing approach to create a hybrid device that integrates a FASC with a fiber-shaped temperature sensor (FTS).

Methods

The core innovation lies in a 3D printing method for fabricating integrated fiber-shaped electronic devices. The process involves:

  • Ink Preparation: Developing specialized inks containing active materials (V₂O₅ for the positive electrode, VN for the negative electrode) and conductive additives (SWCNTs) for the supercapacitor, and reduced graphene oxide (rGO) for the temperature sensor. These inks exhibit shear-thinning behavior, crucial for controlled extrusion in 3D printing.
  • 3D Printing: Utilizing a custom-built 3D printer to extrude these inks into fiber structures. The printing process involves extruding the inks below the surface of a coagulation bath (PVA aqueous solution), allowing for immediate solidification and the formation of continuous fibers. This method allows for the creation of various fiber patterns, such as Archimedean and hexagonal spirals.
  • Electrolyte Integration: Printing a PVA/KOH gel electrolyte onto the fabricated electrode fibers to form the supercapacitor.
  • Device Assembly: Twisting the positive and negative electrode fibers together to create the fiber-shaped asymmetric supercapacitor (FASC). The FTS, made from rGO fiber, is then integrated with the FASC.
  • Characterization: Employing a suite of techniques including Field Emission Scanning Electron Microscopy (FESEM) and Transmission Electron Microscopy (TEM) for structural analysis, X-ray Diffraction (XRD) and Raman spectroscopy for material phase identification, and X-ray Photoelectron Spectroscopy (XPS) for surface elemental analysis. Electrochemical performance was evaluated using Cyclic Voltammetry (CV), Galvanostatic Charge/Discharge (GCD), and Electrochemical Impedance Spectroscopy (EIS).

Datasets

Not discussed in the paper. The paper focuses on the fabrication and characterization of a novel device rather than training or evaluating on existing datasets.

Key Insights and Ideas

  • Scalable 3D Printing for Wearables: The paper demonstrates that 3D printing is a viable and scalable method for producing complex, fiber-shaped electronic components for wearable applications, overcoming limitations of traditional fabrication techniques.
  • Integrated Energy and Sensing: The successful hybridization of a supercapacitor and a temperature sensor into a single fiber showcases a significant step towards self-powered wearable systems that can both store energy and monitor environmental or physiological parameters.
  • Shear-Thinning Inks are Key: The development of rheologically optimized inks with shear-thinning properties is critical for achieving precise extrusion and forming stable, continuous fibers during the 3D printing process.
  • High Performance in a Fiber Format: The fabricated FASC exhibits excellent specific capacitance and energy density, outperforming many previously reported fiber-shaped supercapacitors.
  • Sensitive and Flexible Temperature Sensing: The integrated rGO-based temperature sensor demonstrates high sensitivity and a linear response, making it suitable for accurate temperature monitoring in wearable contexts.

Key Results

  • Fiber-Shaped Asymmetric Supercapacitor (FASC):
    • Achieved a high specific capacitance of 116.19 mF cm⁻² at a current density of 0.6 mA cm⁻².
  • Demonstrated excellent flexibility, with CV curves remaining largely unchanged after bending up to 180°.
  • Showed remarkable capacitance retention of 94.7% after 4000 bending cycles.
  • Achieved an energy density of 41.28 µWh cm⁻² at a power density of 480 µW cm⁻², outperforming many existing fiber-based supercapacitors.
  • Maintained 91.9% capacitance retention after 8000 charge-discharge cycles.
  • Fiber-Shaped Temperature Sensor (FTS) and Integrated Device:
    • The integrated FASC/FTS device can provide a stable output voltage of 1.6 V to power the FTS.
  • The temperature responsivity of the integrated device was measured to be 1.95% °C⁻¹, which is significantly higher than reported values for CNTs and commercial platinum sensors.
  • The resistance of the integrated device decreases linearly with increasing temperature, indicating ohmic contact and a reliable sensing mechanism.
  • The device exhibits rapid response and recovery times (within seconds) and high-temperature resolution.

Limitations and Future Work

  • Limitations:
    • The paper mentions that the "larger planar structure limits the development of wearable energy storage devices" in previous studies, implying that while their fiber format is an improvement, further optimization for ultra-thin or conformable applications might be explored.
  • While the flexibility is good, the long-term durability under extreme mechanical stress or repeated harsh bending cycles might require further investigation.
  • The paper focuses on a single temperature sensor integrated with a supercapacitor. Future work could explore integrating multiple sensors or more complex electronic circuits.
  • Future Work:
    • The authors suggest that this 3D printing technique opens new opportunities for flexible, wearable, fiber-shaped, integrated electronic devices.
  • Further research could focus on optimizing the materials and printing parameters for even higher performance and exploring a wider range of sensing functionalities and energy storage capacities.
  • The development of more complex integrated systems for advanced health monitoring and human-machine interfaces is a promising avenue.

Summary updated

Abstract

Wearable fiber-shaped electronic devices have drawn abundant attention in scientific research fields, and tremendous efforts are dedicated to the development of various fiber-shaped devices that possess sufficient flexibility. However, most studies suffer from persistent limitations in fabrication cost, efficiency, the preparation procedure, and scalability that impede their practical application in flexible and wearable fields. In this study, a simple, low-cost 3D printing method capable of high manufacturing efficiency, scalability, and complexity capability to fabricate a fiber-shaped integrated device that combines printed fiber-shaped temperature sensors (FTSs) with printed fiber-shaped asymmetric supercapacitors (FASCs) is developed. The FASCs device can provide stable output power to FTSs. Moreover, the temperature responsivity of the integrated device is 1.95% °C<sup>-1</sup>.
BibTeX
@inproceedings{zhao2018d,
  author = {Jingxin Zhao and Yan Zhang and Yinan Huang and Jixun Xie and Xiaoxin Zhao and Chaowei Li and Jingyi Qu and Qichong Zhang and Juan Sun and Bing He and Qiulong Li and Conghua Lu and Xinhua Xu and Weibang Lu and Liqiang Li and Yagang Yao},
  title = {{3D Printing Fiber Electrodes for an All‐Fiber Integrated Electronic Device via Hybridization of an Asymmetric Supercapacitor and a Temperature Sensor}},
  booktitle = {Advanced},
  year = {2018},
  doi = {10.1002/advs.201801114},
}
Figure