1008 The Improvement of Tribological and Fatigue Properties of Aluminum Alloy Coated DLC

Yuta Suzuki, Hideto SuzukiThe Proceedings of Ibaraki District Conference 2007 · DOI

Abstract

Aluminum alloys are widely used in industry due to their lightness, recyclability, and corrosion resistance. However, their poor wear resistance often necessitates the use of Diamond-Like Carbon (DLC) coatings. A common concern is that the high-temperature history of traditional coating processes can degrade the fatigue strength of the aluminum substrate. This study investigates a low-temperature coating process using Unbalanced Magnetron Sputtering (UBMS) to apply a nanostructured DLC film. By utilizing a Tungsten-doped interlayer and a laminated nanolayered DLC structure, researchers achieved significant improvements in both wear resistance and fatigue strength compared to the uncoated substrate.

Introduction

Aluminum alloys, such as A6061, are essential in modern manufacturing for weight reduction and energy efficiency. Despite their advantages, their "soft" surface leads to rapid wear in tribological applications. While DLC coatings offer a solution for wear, the heat involved in conventional deposition often over-ages the alloy, creating a trade-off between surface hardness and structural fatigue life. This paper explores a methodology to provide both high wear resistance and improved fatigue performance through a low-temperature deposition technique.

Methodology

The researchers employed Unbalanced Magnetron Sputtering (UBMS) to maintain a processing temperature below 150°C, preserving the mechanical properties of the A6061 alloy. The coating design consists of a 2μm Tungsten-doped (W-DLC) interlayer for enhanced adhesion, followed by a 1μm laminated DLC layer composed of 10 alternating nanolayers. Testing involved ball-on-disk friction experiments and hydraulic servo fatigue tests at 30Hz to compare the virgin material with the DLC-coated specimens.

Tribological Performance

The DLC coating provided a stable and significantly lower friction coefficient compared to the virgin aluminum. Experimental results show that while the uncoated material exhibited a volatile friction coefficient around 0.5, the DLC-coated material maintained a steady value of approximately 0.15 throughout the testing distance. This reduction is attributed to the coating's ability to prevent adhesive wear.

Comparison of friction coefficient between virgin and DLC-coated aluminum alloy over sliding distance.

Fatigue Strength Enhancement

One of the most significant findings is that the low-temperature UBMS process did not weaken the part; instead, it resulted in a 10% increase in fatigue strength. The S-N curves (Stress vs. Number of cycles to failure) demonstrate that the DLC-coated specimens consistently outperformed the virgin material, indicating that the coating process successfully avoided the detrimental effects of high-temperature over-aging.

S-N curves showing the fatigue test results for virgin and DLC-coated aluminum alloy.

Discussion: The Constraint Effect

The improvement in fatigue life is linked to a "constraint effect" provided by the high-modulus DLC coating. In standard A6061, fatigue cracks typically initiate at the surface where precipitates debond from the aluminum matrix. The DLC coating acts as a structural girdle, constraining surface micro-deformation and delaying crack initiation. SEM analysis confirmed this shift, showing that failure in coated specimens moved from surface inclusions to internal shear slip within the matrix.

Conclusion

The use of low-temperature UBMS to apply nanostructured DLC coatings effectively addresses the traditional weaknesses of aluminum alloys. By achieving a stable, low friction coefficient and a 10% boost in fatigue strength, this method offers a robust solution for high-performance industrial components. Future work will investigate the long-term thermal stability of these coatings and further optimize the nanolayer architecture to push performance limits even further.

Summary updated

Abstract

Aluminum alloy has been used in several kinds of industries against a background of environmental problem and energy saving because aluminum alloy has a lot of advantages; lightness, recyclability and good corrosion resistance. However, aluminum alloy has poor wear-resistance, so in order to solve this problem, DLC (Diamond Like Carbon) coating which indicates high tribological properties was performed. However, there are some reports which are con-cerned that coated materials like DLC indicate low fatigue strength compared with substrate only due to high heating history during the coating process. So, in this study, in order to improve wear resistance and to (i) coating process was performed by using UBMS (Unbalanced Magnetron Sputtering) method, and (ii) inter-layer which was doped Tungsten was formed on the substrate, and on the inter-layer (iii) two kinds of DLC coatings were laminated for nano order. Wear tests and fatigue tests were carried out. Aluminum alloy coated DLC indicated very low wear rates, excellent tribological properties. Furthermore, it indicated high fatigue strength compared with substrate only.
BibTeX
@inproceedings{suzuki2007improvement,
  author = {Yuta Suzuki and Hideto SUZUKI},
  title = {{1008 The Improvement of Tribological and Fatigue Properties of Aluminum Alloy Coated DLC}},
  booktitle = {The Proceedings of Ibaraki District Conference},
  year = {2007},
  doi = {10.1299/jsmeibaraki.2007.247},
}
Figure