The increasing demand for high-voltage integrated circuits (HVICs) in automotive and display technologies necessitates efficient gate drivers. While thin-gate HV-MOSFETs offer high transconductance and low cost, they are susceptible to gate-oxide breakdown. This paper presents a regulated gate driver that operates from a 7V-to-30V supply using standard 5V low-voltage (LV) components. By employing a dual-loop architecture and source-follower protection, the design achieves a 190A/µs transient current response and a 52V/µs slew rate while maintaining thin-gate reliability.
Introduction
High-voltage MOSFETs (HV-MOSFETs) are essential for HVICs but present a design challenge. Thick-gate devices are robust but suffer from low transconductance ($g_m$) and high costs. Thin-gate devices are faster and cheaper but fragile; high gate-to-source voltage ($V_{GS}$) causes immediate breakdown. Existing solutions often rely on expensive processes like Silicon-on-Insulator (SOI) or consume significant area and power. This work introduces a driver that provides high current-driving capability for large capacitive loads using a standard CMOS process.
Proposed Architecture and Methods
The proposed "regulated driver" architecture utilizes only two thin-gate HV transistors, with the remainder of the circuit composed of standard 5V LV devices. The design features a dual-loop architecture:
Voltage-Regulation (VR) Loop: A low-voltage error amplifier and feedback network ensure a stable 4.8V output to protect the load.
Fast Source-Follower (SF) Loop: An internal high-speed loop provides immediate current boosts during load transients, enabling high-speed operation.
Proposed regulated gate driver architecture (a) and its dual-loop control mechanism (b).
To protect the sensitive thin-gate oxides, the design uses a source-follower configuration to clamp voltages. The source voltage tracks the gate voltage, ensuring $V_{GS}$ never exceeds 5V, even with a 30V supply. Stability is maintained via a pole-zero cancellation network ($R_1, R_2, C_1$) that mitigates ringing when driving large capacitive loads. Additionally, a "break-before-make" dead-time circuit prevents shoot-through current, enhancing power efficiency.
Experimental Results
The design was fabricated in a 0.5µm standard 5V/40V CMOS process and tested with a 270pF load. Key results include:
Transient Response: Achieved a transient current of 190A/µs and a slew rate of 52V/µs.
Power and Area: Consumes only 4mW of power and occupies a compact area of 0.13 $mm^2$.
Stability: Bode plots confirm the effectiveness of the pole-zero cancellation, showing improved phase margins (e.g., from 57.47° to 77.08° in the 'Driver ON' state).
Stability response showing the effect of pole-zero cancellation for Driver ON (a) and Driver OFF (b) states.
This research demonstrates a high-performance gate driver that leverages the benefits of thin-gate HV-MOSFETs within a standard LV CMOS process. The dual-loop architecture and integrated protection mechanisms provide a robust, high-speed, and area-efficient solution for modern high-voltage applications.
Summary updated
Abstract
The growing markets of electronic components in automotive electronics, LCD/LED drivers and TV sets lead to an extensive demand of high-voltage integrated circuits (HVICs), which are normally built by HV-MOSFETs. These HV-MOSFET devices generally occupy large die areas and operate at low speed due to large parasitic capacitance and small transconductance (gm). There are two types of HV-MOSFET devices, namely, thick-gate and thingate oxide devices. Thick-gate oxide devices can sustain a high gate-to-source voltage, VGS, but suffer from a reduced gm, poor threshold voltage VT control in production and higher cost due to the need of extra processing steps. Thin-gate devices have a larger gm, smaller parasitic capacitance, less processing steps and a lower cost. These properties make the thingate HV-MOSFETs attractive, though they face severe limitation on VGS swing. There are two main concerns when thin-gate HV-MOSFETs are used. The first is how to achieve high current driving capability to drive capacitive loads in high-voltage (HV) application, whereas the second is how to protect the thin-gate oxide from HV stress breakdown. For current-driving capability, Bales (Bales, 1997) proposed a class-AB amplifier using bipolar technology which consumes a high quiescent current and is expensive due to a large die area and complicated masking. Lu & Lee (Lu & Lee, 2002) proposed a CMOS class-AB amplifier which can only drive around 6mA and does not meet the driver requirements of large and fast current responses (Hu & Jovanovic, 2008). Mentze et al. (Mentze et al., 2006) proposed a HV driver using pure low-voltage (LV) devices but this architecture requires an expensive silicon-on-insulator (SOI) process to sustain substrate breakdown in HV application. Tzeng & Chen (Tzeng & Chen, 2009) proposed a driver that consumes a large die area with all transistors inside the circuit being HV transistors. On the other hand, transistor reliability becomes a serious issue in HV thin-gate oxide transistor circuits. Chebli et al. (Chebli et al., 2007) proposed the floating gate protection technique. The voltage range under protection will change according to the ratio of capacitors and the HV supply, VDDH. This technique, however, cannot limit the voltage across the nodes of gate and source well when the variation of the supply voltage is large. Riccardo et al. (Riccardo et al., 2001) proposed a method which requires an extra Zener diode to protect the thin-gate oxide transistors, so a special process and higher cost are incurred. Declercq et al. (Declercq et al., 1993) suggested a HV-MOSFET op-amp driver with a clamping circuit to protect the thin-
BibTeX
@inproceedings{ng2010v,
author = {David C. Ng and Victor So and H. K. and David K. K. Kwong and Ngai Wong},
title = {{A 7V-to-30V-Supply 190A/µs Regulated Gate Driver in a 5V CMOS-Compatible Process}},
booktitle = {InTech},
year = {2010},
doi = {10.5772/8629},
}