Temporal Resource Partitioning for Wireless Information and Power Transfer

74 concepts66 papers1 proposal

Radio frequency (RF) signals carry both energy and information. This dual nature underpins Simultaneous Wireless Information and Power Transfer (SWIPT), a paradigm aimed at creating self-sustaining wireless networks where devices harvest energy from the very signals that communicate with them.

However, capturing both energy and data from a single radiation field introduces a fundamental physical conflict. Information decoding requires linear, low-noise amplification to distinguish subtle variations in phase and amplitude. Conversely, energy harvesting requires routing raw RF power into a diode-rectifier circuit to convert alternating current to direct current (DC)—a highly non-linear process that operates efficiently only at high input voltages.

To bypass this conflict, early architectures attempted to split the received signal's power into two parallel paths using analog hardware. This approach compromises both objectives: the information decoder receives a attenuated signal, lowering data capacity, while the energy harvester receives less peak power, often falling below the activation threshold of the rectifying diodes.

The breakthrough idea that resolves this tension is temporal resource partitioning—often operationalized as the harvest-then-transmit or time-switching protocol. Instead of splitting the signal's power simultaneously, the system splits the resource across time.


The Core Mechanism: Time-Switching

In its simplest form, a time-switching architecture divides a single communication coherence block into distinct, non-overlapping phases.

Receiver-Side Time-Switching:
+---------------------------------+---------------------------------+
|   Energy Harvesting Phase (α)   |  Information Decoding Phase     |
|   (100% RF to Rectifier)        |  (100% RF to Baseband/ADC)      |
+---------------------------------+---------------------------------+
<--------------------------- Total Time Block ---------------------->

During the first phase, spanning a fraction of the time block $\alpha$, a simple RF switch routes 100% of the incoming signal directly to the energy harvesting circuit. Once the device accumulates sufficient energy, the switch toggles for the remaining fraction $1-\alpha$, routing the entire signal to the information decoder.

As Chen–Feng Liu et al. demonstrate in Simultaneous Wireless Information and Power Transfer Under Different CSI Acquisition Schemes, this temporal separation allows battery-less terminals to capture and store energy from an external Access Point (AP) before using that exact energy to power subsequent decoding and feedback operations. By avoiding complex analog power splitters, the receiver hardware remains simple, low-cost, and highly efficient.


Why It Works: Transmit-Side Degrees of Freedom

The true power of temporal partitioning emerges when the time-switching mechanism is shifted from the receiver to the transmitter. In transmit-side time-switching, the base station alternates between broadcasting dedicated energy beams and dedicated data beams.

In a multi-antenna system, a single spatial beamforming vector cannot simultaneously maximize energy delivery to a rectifier and data throughput to a decoder. Energy beamforming requires focusing all spatial degrees of freedom toward the strongest channel path (often via conjugate beamforming) to maximize raw received power. Data beamforming, however, must balance signal strength with interference mitigation (often via zero-forcing beamforming) to maximize the Signal-to-Interference-plus-Noise Ratio (SINR).

Ali A. Nasir et al. analyze this trade-off in Beamforming Design for Wireless Information and Power Transfer Systems: Receive Power-Splitting Versus Transmit Time-Switching. By decoupling energy and information transmission into distinct time intervals, the transmitter can optimize its beamforming vectors independently for each task:

$$\mathbf{w}_{\text{energy}} = \arg\max \mathbb{E}[P_{\text{harvested}}]$$ $$\mathbf{w}_{\text{data}} = \arg\max \text{Rate}(\text{SINR})$$

The authors prove that this temporal decoupling completely avoids the performance compromises inherent in power-splitting systems. Furthermore, as Hongwen Yu et al. show in the context of Reconfigurable Intelligent Surface (RIS)-aided systems, separating these phases allows the environment itself to shift shapes, optimizing its reflection coefficients for maximum power transfer in one microsecond, and zero-forcing data delivery in the next.


Exploiting Non-Linearity and Interference

Temporal partitioning yields two counter-intuitive advantages rooted in the physics of wireless propagation and hardware design.

1. Maximizing Rectifier Efficiency

Real-world RF-to-DC rectifiers are highly non-linear. Their conversion efficiency is an S-shaped (convex-concave) curve: at low input powers, the diode does not turn on, yielding near-zero efficiency; at high powers, it saturates.

Ganggang Ma et al. explore this in Time-Division Energy Beamforming for Multiuser Wireless Power Transfer with Non-Linear Energy Harvesting. If a transmitter splits its power continuously over time, the received power at a distant node might hover below the rectifier's activation threshold. By compressing the energy delivery into a short, high-intensity temporal burst during the harvesting phase, the transmitter pushes the receiver's diode into its peak efficiency region, yielding significantly more total harvested DC energy than continuous, low-power transmission.

2. Turning Interference into an Asset

In conventional communications, co-channel interference from neighboring transmitters degrades the SINR and ruins data decoding. However, an energy harvester does not care about the phase, structure, or source of an RF wave—it only cares about its raw electromagnetic variance.

In Wireless Information and Energy Transfer in Multi-Antenna Interference Channel, Chao Shen et al. reveal that in high-interference environments, time-division strategies routinely outperform "ideal" simultaneous transfer models. During the dedicated energy phase, receivers treat all incoming signals—including what would normally be destructive interference—as a valuable source of harvestable energy. The system effectively scavenges ambient chaos for power, then transitions to a clean, coordinated time slot for data transmission.


Application to Network Topologies

The harvest-then-transmit principle scales naturally across diverse network architectures, providing a predictable framework for resource allocation.

  • Wireless Powered Communication Networks (WPCNs): In a foundational framing, Lingjie Duan demonstrates in Spatial Throughput Maximization of Wireless Powered Communication Networks how a sequential downlink-energy and uplink-information phase enables scalable deployments of battery-free IoT devices with minimal coordination overhead.
  • Relay Networks: In cooperative relaying, an energy-constrained intermediate node must harvest power from a source before forwarding its data. Caijun Zhong et al. show in Wireless Information and Power Transfer with Full Duplex Relaying how time-switching protocols allow full-duplex relays to capture energy from a source signal and immediately apply that stored energy to forward data, eliminating the spectral efficiency penalties that plague traditional half-duplex cooperative systems.
  • Cognitive Radio: In spectrum-sharing scenarios, Rui Zhang 0006 demonstrates that secondary users can utilize a harvest-then-transmit protocol to scavenge energy from a primary user's active transmission phase, subsequently using that harvested energy to transmit their own data without causing harmful interference.

By transforming a complex multi-objective physical conflict into a clean, mathematically tractable scheduling problem, temporal resource partitioning provides the foundational protocol layer that makes self-powered, wireless-charging networks practically viable.

History & citationVersion 1 · 2026-10-04

Current · Permanent link

View frozen version 1

Cite this direction

Latest version (a living page):

@misc{lacuna_harvest_then_transmit_protocol_394c4b83,
  title = {harvest-then-transmit protocol},
  author = {{Lacuna}},
  howpublished = {Lacuna research direction},
  year = {2026},
  url = {https://lacuna.tiptreesystems.com/direction/harvest-then-transmit-protocol/rdr_394c4b83a6bc410c8992263c9c71424e},
  note = {Latest version of a living research direction; cite a version for a fixed text. Accessed 2026-11-19},
}

This exact version (version 1, frozen text):

@misc{lacuna_harvest_then_transmit_protocol_394c4b83_v1,
  title = {harvest-then-transmit protocol},
  author = {{Lacuna}},
  howpublished = {Lacuna research direction},
  year = {2026},
  url = {https://lacuna.tiptreesystems.com/direction/harvest-then-transmit-protocol/rdr_394c4b83a6bc410c8992263c9c71424e/v/1},
  note = {Version 1, frozen 2026-10-04. Accessed 2026-11-19},
}
About

These directions overlap with this one through shared papers.

See something wrong? Report a mistake